Brakelight switch for handlebar mounted master cylinder

Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815. See ELA30861 for less expensive alternative part. Sometimes supplied with three terminals, in this instance disregard middle terminal

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30749860 GU30749860 30 74 98 60
 3074 9860 3074.9860 30.74.98.60

Brakelight switch for handlebar mounted master cylinder

Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.

 1 in stock

 30749860 GU30749860 30 74 98 60
 3074 9860 3074.9860 30.74.98.60

Self adhesive cable tie block for securing cables to bodywork and panels, particularly useful where cables must be kept out of the way under the rear mudguard. Simply stick block to bodywork, route cable tie through bracket on block and round wiring

Wiring clip. One block

 More than 5 in stock

Ignition condenser for Motoplat systems, one required per bike

 Sorry, this part is no longer available.

 27710435 GU27710435 27 71 04 35
 2771 0435 2771.0435 27.71.04.35

Cut out switch, threaded body. Used as sidestand switch on big twins and clutch cut out switch on V7 series small twins and Breva 750

 This part is available by special order, request a quote

 29759150 GU29759150 29 75 91 50
 2975 9150 2975.9150 29.75.91.50

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote

Insulated medium female bullet connector

Crimp type

 More than 5 in stock

Female crimp connector for male Superseal connector blocks

 More than 5 in stock